podcastferro.blogg.se

1. JTAF KEYVAULT CHECKER INSTALL
2. JTAF KEYVAULT CHECKER UPDATE
3. JTAF KEYVAULT CHECKER RAR
4. JTAF KEYVAULT CHECKER FREE

You also want to make sure your cable is short as possible.Ī Proper test to Check If You are Still Exploitable If you skipped out on the diode, try adding one, and just restarting your computer has fixed the issue quite a few times for me. If you are having issues having nandpro detecting it, go over and double check all of your soldering. You only have a problem if can't read block after block, which means something went wrong in the middle of the dump and you have to restart it again.) (If during the dump it has trouble reading blocks, don't worry. Type nandpro lpt: -r16 nand2.bin and dump it a second time.(This is just to be safe) Now it will start the dump which can take from 20 minutes to 40 minutes. Plug the lpt cable in,and open up your cmd-change directories to your nandpro folder! Now plug your xbox 360 in, but don't power it up!

JTAF KEYVAULT CHECKER INSTALL

Install the file 'port95nt.exe' (if running vista or 7 set it for compatibility mode for xp.)

JTAF KEYVAULT CHECKER RAR

Oh and i forgot to add the nandpro, so get that hereĮxtract the rar files and open the nandpro folder. There has recently been a new technique which has hit the net, which is supposedly better, though i have not attempted to try this, but have a look anyway lol

JTAF KEYVAULT CHECKER FREE

I suggest using at least a 30w iron as a 15w will have trouble getting the lead free solder hot enough.All resistors on the connector are optional, it's just to prevent damage as some ports are 5v and the motherboard is 3.3v. You actually don't need any solder for the motherboard end, as the holes all have solder in them.So really, you just need to heat it up, and slide the wiring through. Soldering is fairly straight forward at the end of the day, it just requires a steady hand and lots of patience. Now That You Have Your Parts, Lets Get Properly Started lol But I would suggest going with it instead since it is supposed to be electrically superior and uses less parts so less room for failure I guess. I've never used this method before so I can't really help as much if you have problems.

JTAF KEYVAULT CHECKER UPDATE

There has been a new update to the standard wiring you should use for the JTAG wiring on Xenon's which requires just 2x 1n4148 diodes. Look at image to see which motherboard you Have ie an old printer.ġx 25 pin d-sub connector (male or female depending on which kind of cable you have)ġx 25 pin d-sub cable (lpt cable) You can actually skip the cable if you buy a male connector and make your wires long enough to extend from your xbox to the computerĭigikey # AE9863-ND- again, search up if unsureģx 330 ohm resistors ( only for Xenon motherboards)ĭigikey # P330BBCT-ND -again, search up if unsureġx 1n4148 switching diode (if you have Zephyr, Falcon, Opus or a Jasper get 3x of these)

Note- You should have already dertermined if Your 360 is J-taggable, See Here!Ĭomputer with LPT port. Also, just so you know, this hack just replaces the KK-Hack, but this exploit is just tonnes faster, easier and works on a wider range of 360s. This works for all hardware types though, eg zephyr, jasper, xenon. All that we need to know for now, is that there is a new way to exploit the kernel of an xbox 360 with a dashboard under 8XXX- see my j-tag page for more details. This hack can boot homebrew in less than 5 seconds.